|
|
|
|
|
 |
|
|
|
|
 |
|
IHRA-Tech
e-Bulletin 6. 31st January 2020 |
SAFETY
BELT / HARNESS |
|
 |
|
General Reg 5910, Safety,
Interior, Safety belt/harness
In good condition and securely fastened
to the frame or reinforced mounting
point.
Mandatory |
|
General Reg 5910, Safety,
Interior, Safety belt/harness
Reinforcement are minimum of 75mm (3
inches) by 75mm (3 inches) by 3mm (1/8
inch) steel plate.
Mandatory |
|
General
Reg 5930, Safety, Interior, Safety
belt/harness
All harnesses must be labelled or
stamped by the manufacturer with their
product date or an expiration (used by)
date. Harness to be no older than 10
years from date of manufacturer. Onus is
on the competitor/owner to ensure that
all Harnesses are in date. Out of date
Harnesses will require exclusion from
the event on the day.
Mandatory |
|
General Reg 5940, Safety,
Interior, Safety belt/harness
Fitted as recommended by the
manufacturer, using the supplied
hardware.
Mandatory |
|
General
Reg 5950, Safety, Interior, Safety
belt/harness
Bolts penetrate through belt webbing.
Forbidden |
|
General
Reg 5960, Safety, Interior, Safety
belt/harness
Webbing crosses any surface sharper than
a diameter of 10mm (3/8 inch)
Forbidden |
|
General Reg 5970, Safety,
Interior, Safety belt/harness
Protective plates installed where belts
wrap around any section of the fram
which is exposed to abrasion.
Mandatory |
|
General Reg 5980, Interior,
Safety belt/harness
If seat is mounted in the upright
position, then straps mounted as per the
attached image below.
Mandatory |
|
|
General Reg 5990, Safety,
Interior, Safety belt/harness
If seat is mounted in the inclined
position, then straps mounted as per the
attached image above.
Mandatory |
|
General Reg 6000, Safety,
Interior, Safety belt/harness |
If the two shoulder straps join prior to
a common mounting point, then the
junction of the belts is at least six
inched behind the drivers neck.
Mandatory |
|
General Reg 6010, Safety,
Interior, Safety belt/harness
If safety belts incorporate a lever type
centre buckle, then fitted with a quick
release cover of flap to prevent
accidentally release of the buckle.
Mandatory |
|
General Reg 6030, Safety,
Interior, Safety belt/harness
If sedan and slower than 12.00 seconds
(1/4 mile equivalent) or is a Modern
Street Vehicle and is slower than 10.00
(1/4 mile equivalent) and running at
Off-Street Event, then minimum of quick
release, lap/sash (three-point) type
required, complying with Australian
Standard E35 or AS2596. For the purpose
of these rules, a Modern Street Car is
one that was delivered from factory with
a minimum of a drivers air bag and four
wheel disc brakes.
Mandatory |
|
General
Reg 6030, Safety, Interior, Safety
belt/harness
If sedan and quicker than 11.00 (1/4
mile equivalent), or faster than 110mph
(176 kph) then minimum of four-point
harness that complies at least with
Australian Standard E35 or AS/NZ 2596
Mandatory |
|
 |
|
General
Reg 6040, Safety, Interior, Safety
belt/harness
If sedans, Dragster, Altered or Funny
Car, and with a known performance of
more than 200mph (320 kph) then complies
to SFI 16.1 or FIA 8853/98
Mandatory |
|
General Reg 6050, Safety,
Interior, Safety belt/harness
If sedans, Dragster, Altered or Funny
Car, and with a known performance of
more than 200 mph (320 kph), then no
older than 3 years from date of
manufacturer and/or must not exceed
expiration date, or FIA 8853/98 and be
no older than 5 years from date of
manufacturer and/or must not exceed
expiration date..
Mandatory |
|
 |
|
|
|
|
|
|
|
|
|
IHRA AUSTRALIA PTY LTD ACN:
614 774 980 |
|
Website Powered by: |
 |
|
|
|
|